Foros ZackYFileS - Ver Mensaje Individual - Problema después de carga xilink Rev

Pues haber, localice 2 cosillas interesantes, pero peligrosas a la vez...

Bueno, tan peligrosas como la primera modificación del xilinx que realizaste.

Pego el contenido de uno de los documentos para leer adjuntados a lo que encontre.

______________________________________________________________

WARNING !!! WARNING !!! WARNING !!!
DO NOT USE THIS FILE ON FULL WORKING [B]MATRIX REVOLUTION CAM[/B] !!!
THIS IS NOT ORIGINAL DUMP OR " FOUNDED" FILE !!!
THIS FILE IS WRITEN BY ME AFTER TESTING
[B][SIZE="5"]MATRIX - ALL VERSION CAM.[/SIZE][/B]
[COLOR="Red"][B]IF YOU KILL YOUR MATRIX REVOLUTION WITH WRONG XILINX FILE " FOR RELOAD " ,
THEN TRY THIS FILE.[/B][/COLOR]
IF YOU KILL BRAND NEW WORKING REVOLUTION , DON'T BLAME ME !!!
USE AT YOUR OWN RISK !!!
--------------------------------------------------------------------------

File name :[B][COLOR="Red"] Rev_MLC2a.jed[/COLOR][/B]
THIS is same file like version 2 ,only it's compatibile with 3-th patry
Xilinx programmer.
This version support EMULATOR and SMART CARD
Here's second VERSION , TESTED WITH LATEST MRV217 FIRMWARE , KNOT CARD
AND WITH TOPFIELD STB.
It's not yet finished.....new version is comming
MLC

ESTE, parece ser el mismo que ya tenemos, el que cargastes.
--------------------------------------------------------------------------
File name : [B][COLOR="Red"]Rev_MLC2.jed[/COLOR][/B]
This version support EMULATOR and SMART CARD
Here's second VERSION , TESTED WITH LATEST MRV217 FIRMWARE , KNOT CARD
AND WITH TOPFIELD STB.
It's not yet finished.....new version is comming
MLC

Y este la version anterior....
--------------------------------------------------------------------------
[B]File name : Rev_MLC.jed
THIS IS FIRST ZERO VERSION , TESTED WITH LATEST MRV216 FIRMWARE AND WITH TOPFIELD STB.
IN THIS VERSION YOU CAN USE ONLY EMULATOR ,
NO SMART CARD SUPPORT UNTIL I COMPLETE FINISH ALL[/B]
--------------------------------------------------------------------------
How to repair : Easy load latest MRV216 ( bin ) firmware first ,
initialize Cam in STB and when you don't get picture on any of
"emulator" chanel......Remove cam from STB and then load this Xilinx jed file.
Please NOTE : Xilinx chip inside Revolution is Read protected
, so if youuse any other JTAG tool instead original Xilinx Impact
programming software make shure that you erase ( overwrite ) read
protection before write this file in Cam.If you don't have original
Xilinx Impact programming software and programmer ,
you can use any of popular MM/MR JTAG programmers.
Also note that some of them is NOT capable to overwrite
read protection so try to load file few time.
ANY FEEDBACK IS WELCOME
HAPPY NEW YEAR
MLC
-----------------------------------------------------------------
DO NOT USE THIS FILE ON FULL WORKING MATRIX REVOLUTION CAM !!!
IF YOU KILL BRAND NEW WORKING REVOLUTION , DON'T BLAME ME !!!
REMEMBER !!! THIS IS NOT ORIGINAL FILE !!! USE AT YOUR OWN RISK !!!
-----------------------------------------------------------------

__________________________________________________________

Y decía lo de peligroso, porque esto TAMPOCO es especifico para la MATRIX CAM AIR, si ojeamos el mini tuto de programacion del fichero XILINX, podremos ver que se utiliza usando la MATRIX RELOADED como CAM a modificar.

Y ahora vienen la recapitulaciones...
la Matrx Cam Air, podria ser una Revolution o una Reloaded, pero ampliada, con un controlador USB (para el modulo wifi y sus drivers), mas el controlador de la MicroSD...siendo compatible 100% esta actualizacion del xilinx????

Pues me temos, k solo lo sabremos, si haces lo mismo que la primera vez, actualizar y ver que pasa...

Recuerda que es TU DECISION, si quieres los ficheros, te los envio por correo.