|
Help de WCE.
Wce is a emulating program using a season interface and your pc to decode various encryptions using "normal" cams.
Best operating system for your pc for use with WCE is win2000 or newer.
Some parts of the program will also work on older systems,
but encryption switching in conax cam will most likely not work on win98 or win95 !!
To get WCE going, some files are needed.
1) WCE<version>.exe
2) wincardemu.ini
3) eckeys.dat
4) irdeto.dat
5) seca.dat
6) viaccess.dat
7) conax.dat
What WCE can do for you
If you use a conax-cam, WCE can decrypt Conax, Nagra, Irdeto, Betacrypt, Viaccess, TPScrypt and seca.
(not all versions of conax-cams will work for all encryptions,
4.0 cam and embedded conax receivers like Force or Samsung decode all)
In an Irdeto-freecam 2.020 (or Humax 5400) you can decode the same encryptions like in conax-cam 4.0.
(older versions of Freecam (like 2.018) might not support all encryptions)
In a Viaccess cam WCE does decrypt Viaccess channels only (no TPScrypt).
In a seca (Aston) cam, you can only decode seca channels.
Other cams, like MR, Icecrypt, Matrix, joker, etc are neither tested nor supported and may or may not work using WCE.
Most important to get WCE to decode anything are the correct settings in wincardemu.ini.
(and of course the use of valid keys in the .dat files also helps a lot).
CONAX_CAM
If you plan to use WCE in a conax-cam, you have to select defaultmode=2 (conax),
regardless of what type of encryption you want to decode with your conax-cam.
The line defaultconaxmode has to be set to the system you want to decode
(Example: if you want to decode Nagra, defaultconaxmode=n (Nagra)).
As you are using a conax-cam, the settings for com-port and baud-rate and parity for [Conax]
are the only ones you have to have correct for your equipment!!!
Example :when you use com1 on your pc and embedded conax on a force 1133 you need :
[Conax]
port=1
baud=9600
parity=even
direct
Other cams will need different baud rates and/or parity.
To switch to a different encryption while WCE is running,
press "x" on your keyboard, then enter the encryption you want to decode
(0=beta 1702,2=beta 1722, 6=beta 1762, n=nagra, c=conax, v=viaccess, i=irdeto, s=seca)
and press "enter", then press "x" and "enter" again to get the logging back to your screen.
(Attention, this switching off encryptions will only work, if you use at least win2000 on your pc!!)
If you are using win98 or older, you can only switch encryption before you start Wce by choosing a different defaultconaxmode !!
IRDETO_FREECAM
When you want to use an Irdeto-freecam 2.020(or Humax5400), you first of all have to select defaultmode=4 (Irdeto).
The setting of defaultconaxmode is not important. The switching between encryptions in an Irdeto-freecam is automatic.
IMPORTANT : make sure you select the correct "Goodies" settings in your freecam menu.
These settings are working perfect in Freecam 2.020 for all decodable encryptions:
Debug = OFF
ECM = I/V/S/CO/N
Emu = OFF
TPScrypt = ON
As you are using a Irdeto-cam, the settings for com-port and baud-rate and parity for [Irdeto]
are the only ones you have to have correct for your equipment!!!
Example :when you use com2 on your pc and a freecam 2.020 you need :
[Irdeto]
port=2
baud=9600
parity= none
Some versions of freecam might need different baud rates depending on age, hardware inside and PC used.
(mine is working perfect with 9600 baud)
SECA_CAM
When you use a seca-mediaguard cam (aston), you have to select defaultmode=3 (seca).
No other system are decodable with seca-cam.
As you are using a seca-cam only the settings of com-port and baud rate for [Seca] are important.
Example :when using com3 on your pc and an aston 1.05 cam you need :
[Seca]
port=3
baud=11520
parity=even
direct
I have no idea if other seca-cams or embedded seca in some receivers might need different settings.
VIACCESS_CAM
When you use a viaccess-cam or a viaccess embedded receiver, defaultmode=1 is needed.
No other systems are decodable using a viaccess-cam.
As you are using a viaccess-cam, only the settings of com-port and baudrate for [Viaccess] are important.
Example : when you use com1 on your pc and embedded via on force 1133 you need :
[Viaccess]
port=1
baud=9600
parity=even
direct
Real viaccess-cams will need different baudrates and/or parity.
THE .DAT FILES
You can edit the .dat files with any editor you like (notepad is fine) no special Linux-editor needed.
Edit your keys before you start WCE !!
Seca-keys belong in seca.dat, viaccess-keys belong in viaccess.dat, etc.
Important !! Nagra-keys have to be in irdeto.dat !!!
STARTING WCE
Start WCE by double-clicking on the EXE file.
Then start your receiver or reset your cam.
(It might also work the other way around sometimes, but it is not recommended to do so).
SOME REMARKS...
This is a "hobby-project", so WCE is never finished and will be improved in time.
But there are also no guarantees whatsoever for that, or that the program will work on every receiver/cam combination on the market.
There are NO complete and valid key-files included in WCE, update the keys yourself...
WCE is intentionally NOT auto-updating for Nagra and Conax.
Valid data provided it could auto update Viaccess (in a viaccess-cam only),
Irdeto/Betacrypt (both in Conax- and Irdeto-cam) and Seca (only tested in seca-cam).
__________________ KA*N 570
H/W V12.01.A5
S/W V13.05.02
Load V6.1.8v2 (Gryeti),now 2.1.9v4 Fuck BootLoader.
W XP SP2 & Linux varios.
MReloaded & платина
TE21smd Cas+ MReloaded Loader & Season 
1 mtr. Offset in Usals MotSat2
73 & DX on SATTV
TODO KAPUT ...
Última edición por Luis pelox; 06/02/2005 a las 01:59.
|
10/01/2005, 17:04
#1
Season & Wce
como podeis ver es uno doble,pero si interiormente llevan los "sencillos" lo mismo,podrian servir todos o algunos de los modelos de la marca.
,pero como dice la 1ª Ley del Murphy "si funciona no toques 
